Our engineers will provide you with professional answers.

Common precautions:

Detection switch
1. When welding the terminal, if the load is applied to the terminal, there may be looseness, deformation and deterioration of electrical characteristics due to different conditions. Please pay attention when using.
2. Please avoid using water soluble flux because it may corrode the switch during welding.
3. The welding conditions shall be set according to the actual conditions of batch production.
4. If the voltage is below DC3V or the current is below 100A, there may be poor contact. If it is used for the above conditions, please confirm separately.

Power Supply
1. It cannot be cleaned.
2. This product is designed and manufactured on the premise of DC resistance load. When using other loads (inductive load (L), capacitive load (C)), please confirm separately.

Press
1. Please note that the circuit settings (software settings) should be combined into components according to the jitter and vibration specified for each switch type, without any malfunction.
2. Note that it cannot be used continuously for a long time near the upper and lower limits of the temperature range. Please note that it should be within the scope of various environmental tests in the product specification specified in the service conditions.

slide
1. When performing continuous actions near the upper and lower limits of the operating temperature, please note that the operating regulations should be confirmed according to the type of each machine.

rotate
1. Please use the switch designated for automobile use in automobile use. Do not use the switch that is not specified for automobile.
2. When using, pay attention to the position where the amount of movement should be as close as possible to the total amount of movement.

encoder
1. Please note that it should be used in the position with enough room for movement starting from ON.
2. Please note that the restoring force of the switch cannot be used as the driving force of the mechanical part of the combined component.
testing
1. When the PCBs in the process are overlapped and transported, please be careful not to apply lateral force to the operating part.
2. Especially for small and thin switches, please be careful not to apply external force during the installation process of combined parts.

switch
1. When using through hole printed circuit boards and circuit boards other than those recommended, due to the influence of thermal stress, the welding conditions should be fully confirmed in advance.
multi-function:

1. As the bending of the circuit board may cause changes in characteristics, please fully consider the pattern design and layout design.

Operating device
1. When using a circuit board thinner than the recommended one, the switch may float during mounting. Please note.
Touch:
2. If it is used in a dusty environment, dust will enter from the opening, causing contact failure and poor action. Please consider this in advance when designing the combined parts.
3. If corrosive gas is generated from the surrounding materials of the whole machine using the switch, it may cause poor contact and other phenomena, so please make full confirmation in advance

Specially customized
1. Storage method
Product:
1. The product shall be stored in the place where it is delivered at normal temperature and humidity, free from direct sunlight and corrosive gas. It shall be used as soon as possible within 6 months from the date of delivery.
2. After opening, in order to use polyethylene bags to separate from the outside air, please keep them in the same environment as above and use them as soon as possible.
3. Please don't pile up too much.

Slide switch
Precautions during use
1. When welding the terminal, please note that if the terminal is loaded, it may cause looseness, deformation and electrical characteristics reduction according to different conditions.
2. Please avoid using water soluble flux because it may corrode the switch during welding.
3. The welding conditions shall be set according to the actual conditions of batch production.
4. When soldering twice, please do it after the first soldering part returns to normal temperature. Continuous heating may deform the periphery, loosen and drop the terminals and reduce the electrical characteristics.

Power Supply
1. Please do not let the flux flow to the switch from around and above the printed circuit board.

Press
1. After the switch is installed, in order to harden the adhesive of other parts, please contact us when passing through the regenerative hardening furnace.
2. When using through hole printed circuit boards and circuit boards other than those recommended, due to the influence of thermal stress, the welding conditions should be fully confirmed in advance.

slide
1. With pin type, please weld at the pin position. If welding is carried out when the midpoint of the latch is fixed, the latch mechanism may be deformed.
2. It cannot be cleaned.
rotate
1. Especially for small and thin switches, please be careful not to apply external force during the installation process of combined parts.
2. Tighten the mounting screws within the specified strength. If the screw is tightened with a force greater than the specified force, the action will be poor or the screw will be damaged.

encoder
1. Please insert the product body to the specified installation surface and make the installation reach the horizontal state. If it fails to reach the horizontal state, it will lead to poor action.
2. If the voltage is below DC1V or the current is below 10 μ A If it is used below, it may have poor contact. For the above cases, please confirm separately.

testing
1. This product is designed and manufactured on the premise of DC resistance load. If other loads (inductive load (L), capacitive load (C)) are used, please confirm separately.
2. During switch operation, if more than the specified load is applied, the switch may be damaged. Please be careful not to apply more than the specified force on the switch.

switch
1. If it is used in a dusty environment, dust will enter from the opening, causing contact failure and poor action. Please consider this in advance when designing the combined parts.

multi-function
1. If corrosive gas is generated in the surrounding materials of the whole machine using the switch, it may cause poor contact and other phenomena, so please make full confirmation in advance.

Operating device
1. Storage method
The touch type products shall be kept at normal temperature and humidity at the time of delivery, and shall not be exposed to direct sunlight and corrosive gas. Please use them as soon as possible within 6 months from the date of delivery.

Specially customized
1. After opening, polyethylene bags can be used to isolate the air from the outside. Please keep it in the same environment as above and use it as soon as possible.

product
1. Please don't pile up too much.